The Chevrolet Silverado and its mechanically identical twin, the GMC Sierra is a series of full-size pickup trucks manufactured by General Motors and introduced in 1998 as the successor to the long-running Chevrolet C/K line. General Motors continues to offer a GMC-badged variant of the Chevrolet full-size pickup under the GMC Sierra name, first used in 1988 for its variant of the GMT400 platform trucks. GMC created an upscale version of its Sierra 1500 in 2001 called the Sierra C3. For 2002, the name was changed to Sierra Denali.
If the truck has power door locks. Sierra Keyless Remote Programming Instructions. Learn to program the remote to your GMC Sierra. How to Program GM Chevy, Buick, GMC, Cadillac remotes. GMC Sierra Classic remote) 1998 1999 2000. The door panel. The vehicle will lock and.
GM launched a hybrid version of the Silverado/Sierra in 2004, becoming the first ever GM hybrid passenger vehicle. Starting in 2009, General Motors offers a second generation Chevrolet Silverado and GMC Sierra equipped with a Two-Mode Hybrid powertrain and 4-speed CVT. Use this procedure for Classic body style. Locate the Data Link Port. It is located under dash drivers side.
Be sure you know which pins are 8 and 4. (Notice port is wider on top row). Make sure there are metal contact pins in terminals 8 and 4. Connect 8 to 4 with a suitable jumper wire (leave the jumper wire connected throughout the programming procedure).
Make sure you know which terminals are 8 and 4. Nature Objectives And Scope Of Business Ethics Pdf. The vehicle will respond by locking and unlocking the doors to signify entering of programming mode.
Press and hold both the LOCK and UNLOCK buttons together on the first transmitter to be programmed. After about 15 seconds, the vehicle will respond by locking and unlocking the doors. Release the buttons on the transmitter. Within one minute, repeat the previous step on the remaining transmitters to be programmed. Remove jumper wire applied to the OBDII Port. Use this procedure for New Body Style.
Close all doors 2. Insert key into ignition 3. Hold down the power UNLOCK button on the driver's door panel, continue to hold down until instructed to release in step 9.
Perform steps 5 through 8 in a fairly rapid succession. Turn the ignition to the ON position (as far as you can go without starting the engine.) 6. Turn the ignition to the OFF position. Turn the ignition to the ON position (as far as you can go without starting the engine.) 8. Turn the ignition to the OFF position. Release the power UNLOCK button on the door panel.
The vehicle should respond by door locks locking and unlocking automatically. (If locks do not cycle after you let go, not before you let go of the unlock button, then the vehicle has not entered programming mode and you must start procedure over. Remove key from ignition, open drivers door and return to step 1 ). If the locks do cycle automatically then proceed to step 10. Hold down the LOCK and UNLOCK buttons on the remote until the doors lock and unlock. This may take up to 30 seconds. Repeat step 10 NOW for each additional remote. (Including any existing remotes).
Turn the ignition to the ON position to exit the programming mode. Test remote(s). Disclaimer • We do our best to make sure the information viewed on our website is accurate. • We will not be held responsible, however, for technical inaccuracies or typographical errors. • We shall not be held liable for damage or loss due to your use of any programming procedures used from this website. • We do not make any warranties about the procedures listed or about the accuracy of the programming procedures.
• We accepts no responsibility for content, or other problems that may occur from the use of the programming procedures used from this website. License Plate Maker Custom Clipart. How To Find Proxy Settings In Windows Vista.
Chevy, Chevrolet, Cadillac, GMC, Buick, Pontiac and Hummer H2 keyless entry remote programming for trucks and SUVs is quite simple In order to program a Keyless entry remote (sometimes called installation or activation) you simply need your car remote (all of your existing and new GM keyless entry remotes) and your ignition key. Actually, despite the common name - remote programming, the process involves training the GM truck to recognize a new remote you purchased. So within the first few steps of programming the remote, you get the vehicle into so-called programming mode or learning mode, then simply press a button (or buttons) on all the remotes you have.
Please watch use the video aid below to watch how it is done in the truck - how to program keyless entry remote video. Remote programming for most trucks made before 2007.