• TS400 & TS410 Intruder Alarm Control Panels UNSET TAMPER FINAL EXIT HOME AWAY Installation & Programming Instructions. • Initial Power-Up... 13 TS400 Features... 3 TS410 Features. • TS400/TS410 Installation Instructions Overview Overview Introduction Specifications The TS400 and TS410 are 6 zone microprocessor TS400 Control Panel based intruder alarm control panels with 5 240V ±10% 50Hz Input Voltage: programmable zones and a dedicated Final Exit Current: 40mA (normal) 85mA (alarm) zone. • Planning The Installation General TS410 Control Panel The TS400 and TS410 are flexible systems, but care The TS410 control panel is blind panel and as such must be taken in planning the installation to it can positioned out of view, normally in a provide maximum protection with minimum cupboard under the stairs.
• TS400/TS410 Installation Instructions Planning The Installation Detection Devices Smoke/Heat Detectors 12V Smoke or heat detectors may be connected There are several types of detection devices to the system to provide additional protection available which are suitable for domestic against fire. When activated a distinctive internal.
• System Installation TS400/TS410 Installation Instructions System Installation Installing the TS400 Control Panel 4. Re-position the base and secure to the wall using not less than 30mm x No 10 screws. Remove the screw from the top of the control panel and lift away the front cover. • The TS400 and TS410 are equipped with inside the control panel. A 'Battery Protection' circuit so that if a battery is accidentally reverse connected or its voltage is below 4V, a tamper alarm is generated.
The Fire Alarm Store - DF4000-In-Op Menvier DF4000 Installation Manual [DF4000-In-Op] - Menvier DF4000 Installation and Operating Manual. PINST MFAXA2/V1 Issue D. View and Download Menvier Security TS400 installation & programming instructions online. TS400 Control Panel pdf manual download.
• HOME AWAY Leads to transformer A.C. Figure 3 TS400 & TS410 Connection Diagram Bell Fuse 1 - 5 Indicator LEDs This 1 Amp fuse protects the supply to the external These red indicator LEDs indicate the alarm status sounder/bell. Of zone 1 - 5. Note these are not fitted on the TS410. • TS400/TS410 Installation Instructions System Installation To tamper loop for other zones Connecting several flush contacts per zone Flush Contact Flush Contact To tamper loop for other zones Connecting several suface contacts per zone Surface Contact Surface Contact Program [RST-] as. • System Installation TS400/TS410 Installation Instructions Wiring Example External Sounder TS400 / TS410 TRIGGER - ALM - STROBE - RST - HOLD OFF + TRG - HOLD OFF - STB- TAMPER RETURN - TMP - ALARM TAMPER To ZONE 1 Terminal strip. • TS400/TS410 Installation Instructions System Installation the last or furthest remote keypad does not Installing a Remote Keypad exceed 50 metres).
Ensure that the mains and battery power has been disconnected and proceed as follows: 7. Carefully reattach the front cover assembly to the remote keypad base ensuring that all 1.
• System Installation TS400/TS410 Installation Instructions Extension Loudspeakers Aux 12V Power A 16Ohm extension loudspeaker can be The auxiliary 12V terminals provide a permanent connected between the [L/S-] and [AUX 12V+] 12V supply for detectors which require a low terminals. R37 (located in the top left hand corner voltage supply e.g., PIRs, vibration detectors. • TS400/TS410 Installation Instructions System Installation Initial Power-Up On the TS410 you MUST connect the earth 1. Place a small screwdriver blade between the bonding cable from the front cover to the pins on the control panel PCB, marked spade connection point, see figure 2. • Programming TS400/TS410 Installation Instructions Programming Programming Menus There are two programming menus within the system.
The engineer’s programming menu and the user programming menu. The figure below shows the structure of both programming menus, however the engineers programming menu is only covered in full detail within this manual. Program Per Fotomontazh. For full details on the user options see 'User Operating Instructions'. • (Home) condition it will start the entry timer if activated. View Event Log The TS400 will store up to 4 alarm activation events Keyswitch Zone 3 can be programmed as a keyswitch zone, within the memory log. • Programming TS400/TS410 Installation Instructions Exit Time Bell Duration Time This timer sets the delay between the user initiating This timer controls the duration of the external the setting procedure and the system actually sounder when the system is triggered into a full setting. • TS400/TS410 Installation Instructions Programming Setting Mode Remote Reset Number The system can be programmed to set using The 'Engineer Reset' option can be overridden by ether: the user, operating the 'Remote Reset' facility.